Cable Fault Locator (TDR) TX Ranger

TXRanger

New product

The TX Ranger is a hand-held Time Domain Reflectometer (cable fault locator) with a first range of 2.5 meters combined with a 1.3 Nano second pulse width gives a blind zone of only 5 cm, it makes this the ideal product for fault location on short cable assemblies and harnesses. Small and intermittent faults can be easily identified by using the selectable gain control allowing trace amplification of up to 7 times and when set to scan lock mode the advanced noise reduction software may be selected allowing the user to select between 8,16 and 32-point trace averaging further enhancing the clarity of the trace by reducing electrical and environmental interference.

  • Short Range Graphical TDR; 
  • Up to 700m; 
  • Deadzone 0.2m; 
  • Selective Gain; 
  • Trace Comparisons; 
  • USB download to PC. 

More details

Bi Communications

 

On order

859,00 € Tax excluded

0.6 kg

  • USB 2.0 Interface with a Windows compatible software TraceXtra to download/analyse traces
  • Rugged Palm-Top design
  • Weighs less than 350g (12oz)
  • 11 Measurement Ranges up to 6000m(6km)
  • 25, 50, 75 & 100ohm Selectable Cable Impedance
  • Memory capacity upto 50 saved traces
  • Built in Tone Generator for Pair Tracing and Identification
  • Suitable for testing all Communication and Power Cables
  • Environmental Protection IP54
  • CE Approved
  • Soft bag & Test Leads

The TX Ranger is a hand-held Time Domain Reflectometer (cable fault locator) with a first range of 2.5 meters combined with a 1.3 Nano second pulse width gives a blind zone of only 5 cm, it makes this the ideal product for fault location on short cable assemblies and harnesses. Small and intermittent faults can be easily identified by using the selectable gain control allowing trace amplification of up to 7 times and when set to scan lock mode the advanced noise reduction software may be selected allowing the user to select between 8,16 and 32-point trace averaging further enhancing the clarity of the trace by reducing electrical and environmental interference.

With an onboard storage capacity of up to 50 traces including time/date, impedance, Velocity of Propagation, cursor position, range and gain value. These may be recalled and used for comparison with current cables under test or downloaded to the PC via the USB link and TRACEXTRA PC software provided. Historical data stored on the PC may also be uploaded to the Ranger for comparison with current measurements.

Display 128 x 64 pixel (back lit)
Batteries 6 volts 4 x 1.5 AA Alkaline cells
Operating time 20 hours continuous scanning (subject to use of backlight)
Dimensions 165 x 90 x 37 (6.5 x 3.5 x 1.5 ins)
Weight 350 gms (12oz)
Protection class Water/Dust Proof IP54
Operating conditions -10º / 50ºC
Storage conditions -20º / 70ºC
Resolution Approx 1% of range
Accuracy 1% of selected range*
Velocity Factor Adjustable from 1% to 99% or Feet Meters / Micro Second
Memory 50 Traces
Range Meters: 2.5, 5, 10, 20, 40, 80, 160, 320, 640; Feet: 7, 15, 30, 60, 120, 240, 500, 1000, 2000. Manual range control
Sensitivity Min 10 pixel return at 640m on 0.6mm Ø, PE, TP
Gain Preset for Range Scale selected, but with adjustable settings to 7x magnification.
Output Pulse 5 volts peak to peak. Into open circuit
Output Impedance Selectable 25, 50, 75 & 100 ohms
Output Pulse Width 1.3ns, Automatic with range
Scan Rate 2 scans / second or scan held
Trace Averaging User selectable, Disabled, 8, 16 or 32 point trace
Voltage Protection 250 volts AC
Tone Generator 810 – 1100Hz
Power Down Selectable 1, 2, 3 minutes or disabled
Safety IEC 61010-1
Burst EN 60950
EMC BS/EN 61326-1

No customer reviews for the moment.

Write a review

Cable Fault Locator (TDR) TX Ranger

Cable Fault Locator (TDR) TX Ranger

The TX Ranger is a hand-held Time Domain Reflectometer (cable fault locator) with a first range of 2.5 meters combined with a 1.3 Nano second pulse width gives a blind zone of only 5 cm, it makes this the ideal product for fault location on short cable assemblies and harnesses. Small and intermittent faults can be easily identified by using the selectable gain control allowing trace amplification of up to 7 times and when set to scan lock mode the advanced noise reduction software may be selected allowing the user to select between 8,16 and 32-point trace averaging further enhancing the clarity of the trace by reducing electrical and environmental interference.

  • Short Range Graphical TDR; 
  • Up to 700m; 
  • Deadzone 0.2m; 
  • Selective Gain; 
  • Trace Comparisons; 
  • USB download to PC. 
Description Language Ver. Link
TXRanger SW Quick Start Guide English TXRanger QSG, EN
TXRanger Users manual English TXRanger Manual, EN

10 other products in the same category: