Kabelis meklētāja CT45

CT45

Jauns produkts

  • Efficient and versatile cable and wire tracer;
  • For locating telecoms cables & faults and mains house wiring;
  • Helps to distinguish certain cables and wires from others;
  • For tracing buried cables, conduit, sewer-pipes and blockages.

The versatile CT45 cable and wire tracer enables telecom technicians and electricians to locate various types of cables and associated problems. For example, telecom and mains cables, wire pairs, under floor heating cables, cable conduit and even sewer-pipe blockages.

Vairāk informācijas

 

4.2 kg

Pievienot vēlamo produktu sarakstam

The CT45 package includes the CTT45 transmitter, CTR45 receiver and various accessories. The powerful, efficient transmitter ensures an operating distance of up to several kilometres. Together with its sensitive receiver the CT45 combines a flexible setup, which won't let you down even in the trickiest situations.

CTT45 Transmitter

In galvanic usage, in low voltage applications, the CTT45 provides accurate cable tracing or long-range pair identification with wired connection to the target. Fault-spot tracing is also possible with the new 1kHz feeding frequency. For safety, the transmitter has external voltage display and automatic protection mechanisms against high voltages.

Inductive feeding: In high voltage (typically mains) application a PM80 or PM34 clamp on transformer (accessory) can be used.

Inductive feeding above ground (in the image) is useful if the target is an underground cable or a conductive pipeline.

CTR45 Receiver

CTR45 receiver recognizes and traces the 1kHz and 10kHz signals generated by the transmitter. Furthermore it can be used to trace 50Hz mains wires without the transmitter.

Standard setup includes three probes: The inductive rod probe SA1 is ideal for tracing cable routes. The inductive close range probe LA1 is for distinguishing cables from each other or tracing fault-spots and the capacitive probe KA6 is used for identifying wires and pairs.

Receiver has an informative 12 LED bar display for the signal volume. Clear audio volume & signal gain adjustment help adjustment for various tracing conditions such as extended transmission distances or ambient noise.

By using the HM12 headset CTR45 can be used in noisy environment.

How to use CT45

Cable tracing: Defining the route of telecom or mains cables under ground with SA1 probe is one of the most typical cases where the CT45 can be used. The signal can heard from several metre distance and even the cable depth can be closely estimated.

Cable identification: By using the LA1 close range probe it's easy to trace cable inside walls or identify a certain cable among other cables on cable shelves.

Fault-spot tracing: The LA1 probe is used also for so-called fault spot tracing. Using the 1kHz feeding frequency causes minimal cross-talk to other cables and the location of a short circuit in a cable can be found.

Wire Tracing: During installation or renovation work pairs from apartments are easy to find e.g. at house MDF with the capacitive KA6 probe without having to touch the wires.

Tracing cable ducts (conduit) or sewer blockages is based on using the PL18-10 pipe transmitter (accessory). PL18-10 is a water tight independent transmitter which is pushed into the blocked duct or pipe. Also the depth of a blockage can be estimated. For optical micro-ducts special microduct transmitters MPL6-10 and MPL9-10 are available as accessories.

Transmitter indicators LEDs for external voltage, output current, operating mode and power. Buzzer for sound indications.
Transmitter connectors 2pcs. 4mm safety banana jacks
Transmitter trace mode output signal 1024Hz/10,000Hz interrupted or modulated sinusoidal wave (Inductive signal 10,000Hz only)
Transmitter trace mode output impedance Approx. 40V (rms), approx. 450ohms
Transmitter appliance class IP55
Transmitter batteries 6 pcs. IEC LR20 alkaline batteries.
Transmitter power consumption 30 ... 700mA (depending on the mode and load)
Transmitter dimensions ABS, size 248 x 134 x 122mm
Transmitter dimensions Approx. 2.0kg with batteries
Receiving frequencies 1024Hz, 10kHz and 50Hz (‹200Hz)
Receiver probe connector BNC female (for probes) and 3.5mm jack (for headset)
Receiver indicators 12-step LED bar for receiving signal level & 13 other LED indicators. Internal speaker for tracing signal and other audio features
Adjustment 4-step gain adjustment, 4-step audio volume adjustment
Receiver appliance class IP34
Receiver batteries 6 pcs.1.5V IEC LR6 alkaline battery (or similar NiMH cells)
Receiver power consumption 19...120mA (typical 30mA)
Receiver dimensions ABS, size 155 x 90 x 50mm
Receiver weight Approx. 425g with batteries

Šobrid vēl nav klientu atsauksmju.

Uzrakstīt recenziju

Kabelis meklētāja CT45

Kabelis meklētāja CT45

  • Efficient and versatile cable and wire tracer;
  • For locating telecoms cables & faults and mains house wiring;
  • Helps to distinguish certain cables and wires from others;
  • For tracing buried cables, conduit, sewer-pipes and blockages.

The versatile CT45 cable and wire tracer enables telecom technicians and electricians to locate various types of cables and associated problems. For example, telecom and mains cables, wire pairs, under floor heating cables, cable conduit and even sewer-pipe blockages.

Video examples of use of Cable Tracer CT45

CT45 Basic set

The transmitter and receiver use alkaline batteries and both have clear low battery indication. The receiver has an integrated speaker. An external headset can be used for tracing in noisy environment. CT45 is delivered in a handy carrying bag.

1. Transmitter CTT45, 1 psc.
2. Sending cord SJ20 (banana/banana, 2.0m), 1 psc.
3. Crocodile clips, 2 psc.
4. Receiver CTR45, 1 psc.
5. Inductive rod probe SA1, 1 psc.
6. Inductive close range probe LA1, 1 psc.
7. Capacitive probe KA6, 1 psc.
8. Probe cord AK1 (BNC/BNC, 1.0m), 1 psc.
9. Users manual in English, Finnish, Swedish, or Russian, 1 psc.
10. Batteries, 1 set.
11. Carrying bag KPP6, 1 pcs.



Description Language Ver. Link
CT45 Technical description English 1545 CT45 Datasheet, EN

6 produktu tajā pat kategorijā: