Field Phone and Wire Tracer KX15

KX15

Nauja prekė

  • For cable jointing and splicing work;
  • For wire and pair identification;
  • For speech communication.

KX15 is a complete wire tracing equipment with integrated field phone. It is specially designed for cable jointing & splicing work. By using KX15 technicians can quickly indetify right pairs before jointing, particularly with thick multipair cable faults. KX15 consists of a transmitter KXT15 and receiver KXR15. It combines all necessary functions for testing and identifying wire pairs in the field.

Smulkiau

 

KX15 is a complete wire tracing equipment with integrated field phone. It is specially designed for cable jointing & splicing work. By using KX15 technicians can quickly indetify right pairs before jointing, particularly with thick multipair cable faults. KX15 consists of a transmitter KXT15 and receiver KXR15. It combines all necessary functions for testing and identifying wire pairs in the field.

Pair identification method

dr1_web_en.png

Above illustration shows the standard way of using KX15 for pair tracing: After speech communication has been established (A) and (B), (A) connects sending signal to the pair to be traced. (B) can now find the pair with the capacitive probe. When (B) short-circuits the found pair, transmitter will indicate the short-circuit with clear beep as verification.

Wire identification (galvanic method)

dr2_web_en.png

Above illustration shows a galvanic checking method of unused (cold) pairs. By using the step-by-step procedure shortcircuits, cut wires, cross connections and ground leaks can be detected. With special accessories KX15 is suitable for locating cables and detecting pipe blockages.

Tracing cables, sewers and pipes

KX15 can be used also to trace and identify cross-connection pairs and terminal blocks like in the below image.

dr3_web_en.png


KX15 can be used to trace underground or on-shelve cables with the SA10 receiver probe. Sewers and empty pipes and their blockages can be found by inserting the PL18-10 pipe transmitter to the target object. For tracing electric wiring pipes inside houses, pipe transmitter antenna SPA10 is useful when used together with LA1 probe. (SA10, PL18-10 and SPA10 are accessories.)

High impedance pair monitoring

The high impedance, interference-free listen mode of the transmitter KXT15 enables the user to monitor pair before actually sending any signal to it. It is important to use this feature first with pairs that are in use, as in send mode the transmission disturbs possible communication.

If there is DC-voltage on the pair, one of the external voltage LEDs will be lit together with polarity indication. Correspondingly, if there is data on the pair, a special data LED will be lit. Speech e.g. on telephone pairs can be heard through the loudspeaker or headset.

Transmitter indicators 4 voltage LEDs, polarity, data, SEND mode and microphone muting indicator LEDs Loudspeaker for sound indications and high-ohmic listening
Transmitter connectors 2 RCA females (SEND/listening and voice contact), 2 x 3.5mm jacks for headset
Transmitter trace mode output signal 10kHz and 341Hz / 2.5V interrupted square wave
Transmitter batteries 2 pcs IEC 6LR61 alkaline battery
Transmitter dimensions ABS 120x60x24mm, belt clip and wrist band
Transmitter dimensions approx. 170g including battery
Receiver probe connector BNC female (probe connector), RCA female (voice contact), 2 x 3.5mm jacks for headset
Receiver indicators 5 signal level indicator LEDs, power LED, HIGH-mode and microphone muting indicator LEDs, Loudspeaker for listening tracing signal
Receiver operating distance Operating distance up to approx. 7km
Receiver batteries 2 pcs IEC 6LR61 alkaline battery
Receiver dimensions ABS 120x60x24mm, belt clip and wrist band
Receiver weight approx. 170g including battery
Voice connection Impedance 600 ohms, adjustable volume in both units
  • LSA/BNp adapter connects a test equipment with 4mm banana plugs to Krone LSA Plus terminals by breaking (disconnecting) the pair.

  • LSA/BNpk adapter connects a test equipment with 4mm banana plugs to Krone LSA Plus terminals by breaking (disconnecting) the pair. The adapter plug has a fabric reinforced rubber strap. With the strap the adapter can be hung e.g. to a test telephone connecting cord. This way the adapter is always at hand and the strap tightening mechanism prevents the adapter getting lost.

  • LSA/BNv adapter connects a test equipment with 4mm banana plugs to Krone LSA Plus terminals parallel to the pair, i.e. it does not disconnect the pair.

  • LSA/BNvk adapter connects a test equipment with 4mm banana plugs to Krone LSA Plus terminals parallel to the pair, i.e. it does not disconnect the pair. The adapter plug has a fabric reinforced rubber strap . With the strap the adapter can be hung e.g. to a test telephone connecting cord. This way the adapter is always at hand and the strap tightening mechanism prevents the adapter getting lost.

  • Siemens/Krone HVT/MDF71-terminal plug / RJ45-female, for exchange use. Suitable for devices e.g. AP32, AP16, XTT10 and XTT25 (together with RJ-4BNk or RJ-2BN adapter).

  • KP1 adapter is an essential accessory when working with screw terminals. It eases the work and decreases the risk to interfere the communication, as screws don’t have to be loosened and test cords won’t fall away during work. KP1 also has cutting knife contacts that enable connection straight through the insulation of wires.

  • RJ-2BN adapter enables connecting a test device with 4mm banana plugs to RJ sockets. RJ-2BN includes an RJ12 male connector, which is suitable for both RJ11 and RJ45 sockets but does not damage the outermost contacts of the RJ45 like an ordinary RJ11 plug would do. RJ-2BN connects RJ12 pins 3-4 (pair 1) to banana sockets.

  • RJ-4BN adapter enables connecting a test device with 4mm banana plugs to RJ sockets. RJ-4BNk includes an RJ12 male connector, which is suitable for both RJ11 and RJ45 sockets but does not damage the outermost contacts of the RJ45 like an ordinary RJ11 plug would do. RJ-4BNk connects pins 3-4 (pair 1) and 2-5 (pair 2) to corresponding banana sockets. RJ-4BNk is equipped with a switch that...

  • SA10 is a 10kHz tuned amplifying inductive rod probe that is used with XTR25 or KXR15 receivers for cable tracing when the tracing distance is more than 20cm, like with underground cables. SA10 is used in the same way as ordinary SA1 but the tuned construction increases its sensitivity considerably compared to SA1. SA10 is used also when XT25 and KX15 wire tracers are used for locating the...

  • SPA10/20 is an accessory for the Vesala cable tracers. It is suitable for tracing e.g. small empty cable piping routes in buildings, prefabricated hollow wall blockages or non-conductive sewers and their blockages. Usage of SPA10/20 resembles usage of the pipe transmitters, which is an independent transmitter.

  • SJ12 is a universal banana/banana cable to connect e.g. cable tracer transmitter to the target. The same cable is often used as speech connection with older Vesala devices that have speech communication possibility through banana connectors. The banana plugs can be equipped with several different adapters e.g. for different terminal block types. Cable length is 1.2 meters and it has been made...

  • SJ20 is a universal banana/banana cable to connect e.g. cable tracer transmitter to the target. The same cable is often used as speech connection with older Vesala devices that have speech communication possibility through banana connectors. The banana plugs can be equipped with several different adapters e.g. for different terminal block types. Cable length is 2 meters and it has been made of...

  • MPL6 is micro-sized transmitter sonde for tracing microduct and other tube blockages. It has only 6.4mm diameter so it fit into ducts having inner diameter of 8mm or more. MPL6-10 is compatible with Vesala’s 10kHz wire and cable tracers.

  • MPL7 is flexible and only 7mm diameter transmitter sonde for tracing microduct and other tube blockages. It is very useful when new cables are to be pushed into old ducts, which already have installed cables or other obstacles. MPL7-10 is compatible with Vesala’s 10kHz wire and cable tracers.

  • MPL9 is flexible and only 9mm diameter transmitter sonde for tracing microduct and other tube blockages. It is very useful when new cables are to be pushed into old ducts, which already have installed cables or other obstacles. MPL9-10 is compatible with Vesala’s 10kHz wire and cable tracers.

  • PL18 is a small pipe transmitter sonde which is an efficient accessory for the Vesala CL43 Compact Locator and other Vesala cable tracers using the 512kHz (PL18-05) or 33kHz (PL18-33) tracing frequency.

Šiuo metu klientų atsiliepimų nėra.

Parašyti atsiliepimą

Field Phone and Wire Tracer KX15

Field Phone and Wire Tracer KX15

  • For cable jointing and splicing work;
  • For wire and pair identification;
  • For speech communication.

KX15 is a complete wire tracing equipment with integrated field phone. It is specially designed for cable jointing & splicing work. By using KX15 technicians can quickly indetify right pairs before jointing, particularly with thick multipair cable faults. KX15 consists of a transmitter KXT15 and receiver KXR15. It combines all necessary functions for testing and identifying wire pairs in the field.

KX15 Basic set

Transmitter KXT15 basic set

1. Transmitter KXT15, 1 pcs.
2. Connecting cord PJ15p (RCA / 2x4mm banana, 1.5m), 1 pcs.
3. Crocodile clips, 2 psc.
4. Speech cord PJ15 (RCA / banana plugs, 1.5m), 1 pcs.
5. Headset HM12 (3.5 mm plug), 1 pcs.
6. Users manual in English, Finnish, Swedish or Russian, 1 pcs.
7. Carrying case KPP5 (nylon, 240x130x180mm), 1 pcs.
8. Battery, 1 pcs.

Receiver KXR15 basic set

1. Receiver KXR15, 1 pcs.
2. Speech cord PJ15 (RCA / banana plugs, 1.5m), 1 pcs.
3. Crocodile clips, 2 psc.
4. Probe cord AK1 (BNC/BNC, 1.2m), 1 pcs.
5. Capacitive probe KA6, 1 pcs.
6. Inductive probe LA5, 1 pcs.
7. Headset HM12 (3.5 mm plug), 1 pcs.
8. Users manual in English, Finnish, Swedish or Russian, 1 pcs.
9. Carrying case KPP5 (nylon, 240x130x180mm), 1 pcs.
10. Battery, 1 pcs.
Description Language Ver. Link
KX15 Technical description English 1447 KX15 Datasheet, EN
Vesala products catalogue Estonian 08.2016 Vesala catalogue, ET
Vesala products catalogue Russian 08.2016 Vesala catalogue, RU

6 kitos prekės toje pačioje kategorijoje: