Kabelis ieškotojas CT45

CT45

Nauja prekė

  • Efficient and versatile cable and wire tracer;
  • For locating telecoms cables & faults and mains house wiring;
  • Helps to distinguish certain cables and wires from others;
  • For tracing buried cables, conduit, sewer-pipes and blockages.

The versatile CT45 cable and wire tracer enables telecom technicians and electricians to locate various types of cables and associated problems. For example, telecom and mains cables, wire pairs, under floor heating cables, cable conduit and even sewer-pipe blockages.

Smulkiau

 

3.9 kg

The CT45 package includes the CTT45 transmitter, CTR45 receiver and various accessories. The powerful, efficient transmitter ensures an operating distance of up to several kilometres. Together with its sensitive receiver the CT45 combines a flexible setup, which won't let you down even in the trickiest situations.

CTT45 Transmitter

In galvanic usage, in low voltage applications, the CTT45 provides accurate cable tracing or long-range pair identification with wired connection to the target. Fault-spot tracing is also possible with the new 1kHz feeding frequency. For safety, the transmitter has external voltage display and automatic protection mechanisms against high voltages.

Inductive feeding: In high voltage (typically mains) application a PM80 or PM34 clamp on transformer (accessory) can be used.

Inductive feeding above ground (in the image) is useful if the target is an underground cable or a conductive pipeline.

CTR45 Receiver

CTR45 receiver recognizes and traces the 1kHz and 10kHz signals generated by the transmitter. Furthermore it can be used to trace 50Hz mains wires without the transmitter.

Standard setup includes three probes: The inductive rod probe SA1 is ideal for tracing cable routes. The inductive close range probe LA1 is for distinguishing cables from each other or tracing fault-spots and the capacitive probe KA6 is used for identifying wires and pairs.

Receiver has an informative 12 LED bar display for the signal volume. Clear audio volume & signal gain adjustment help adjustment for various tracing conditions such as extended transmission distances or ambient noise.

By using the HM12 headset CTR45 can be used in noisy environment.

How to use CT45

Cable tracing: Defining the route of telecom or mains cables under ground with SA1 probe is one of the most typical cases where the CT45 can be used. The signal can heard from several metre distance and even the cable depth can be closely estimated.

Cable identification: By using the LA1 close range probe it's easy to trace cable inside walls or identify a certain cable among other cables on cable shelves.

Fault-spot tracing: The LA1 probe is used also for so-called fault spot tracing. Using the 1kHz feeding frequency causes minimal cross-talk to other cables and the location of a short circuit in a cable can be found.

Wire Tracing: During installation or renovation work pairs from apartments are easy to find e.g. at house MDF with the capacitive KA6 probe without having to touch the wires.

Tracing cable ducts (conduit) or sewer blockages is based on using the PL18-10 pipe transmitter (accessory). PL18-10 is a water tight independent transmitter which is pushed into the blocked duct or pipe. Also the depth of a blockage can be estimated. For optical micro-ducts special microduct transmitters MPL6-10 and MPL9-10 are available as accessories.

Transmitter indicators LEDs for external voltage, output current, operating mode and power. Buzzer for sound indications.
Transmitter connectors 2pcs. 4mm safety banana jacks
Transmitter trace mode output signal 1024Hz/10,000Hz interrupted or modulated sinusoidal wave (Inductive signal 10,000Hz only)
Transmitter trace mode output impedance Approx. 40V (rms), approx. 450ohms
Transmitter appliance class IP55
Transmitter batteries 6 pcs. IEC LR20 alkaline batteries.
Transmitter power consumption 30 ... 700mA (depending on the mode and load)
Transmitter dimensions ABS, size 248 x 134 x 122mm
Transmitter dimensions Approx. 2.0kg with batteries
Receiving frequencies 1024Hz, 10kHz and 50Hz (‹200Hz)
Receiver probe connector BNC female (for probes) and 3.5mm jack (for headset)
Receiver indicators 12-step LED bar for receiving signal level & 13 other LED indicators. Internal speaker for tracing signal and other audio features
Adjustment 4-step gain adjustment, 4-step audio volume adjustment
Receiver appliance class IP34
Receiver batteries 6 pcs.1.5V IEC LR6 alkaline battery (or similar NiMH cells)
Receiver power consumption 19...120mA (typical 30mA)
Receiver dimensions ABS, size 155 x 90 x 50mm
Receiver weight Approx. 425g with batteries
  • LSA/BNp adapter connects a test equipment with 4mm banana plugs to Krone LSA Plus terminals by breaking (disconnecting) the pair.

  • LSA/BNpk adapter connects a test equipment with 4mm banana plugs to Krone LSA Plus terminals by breaking (disconnecting) the pair. The adapter plug has a fabric reinforced rubber strap. With the strap the adapter can be hung e.g. to a test telephone connecting cord. This way the adapter is always at hand and the strap tightening mechanism prevents the adapter getting lost.

  • LSA/BNv adapter connects a test equipment with 4mm banana plugs to Krone LSA Plus terminals parallel to the pair, i.e. it does not disconnect the pair.

  • LSA/BNvk adapter connects a test equipment with 4mm banana plugs to Krone LSA Plus terminals parallel to the pair, i.e. it does not disconnect the pair. The adapter plug has a fabric reinforced rubber strap . With the strap the adapter can be hung e.g. to a test telephone connecting cord. This way the adapter is always at hand and the strap tightening mechanism prevents the adapter getting lost.

  • Siemens/Krone HVT/MDF71-terminal plug / RJ45-female, for exchange use. Suitable for devices e.g. AP32, AP16, XTT10 and XTT25 (together with RJ-4BNk or RJ-2BN adapter).

  • KP1 adapter is an essential accessory when working with screw terminals. It eases the work and decreases the risk to interfere the communication, as screws don’t have to be loosened and test cords won’t fall away during work. KP1 also has cutting knife contacts that enable connection straight through the insulation of wires.

  • RJ-2BN adapter enables connecting a test device with 4mm banana plugs to RJ sockets. RJ-2BN includes an RJ12 male connector, which is suitable for both RJ11 and RJ45 sockets but does not damage the outermost contacts of the RJ45 like an ordinary RJ11 plug would do. RJ-2BN connects RJ12 pins 3-4 (pair 1) to banana sockets.

  • RJ-4BN adapter enables connecting a test device with 4mm banana plugs to RJ sockets. RJ-4BNk includes an RJ12 male connector, which is suitable for both RJ11 and RJ45 sockets but does not damage the outermost contacts of the RJ45 like an ordinary RJ11 plug would do. RJ-4BNk connects pins 3-4 (pair 1) and 2-5 (pair 2) to corresponding banana sockets. RJ-4BNk is equipped with a switch that...

  • An insulated 4mm safety crocodile clip e.g. for cable tracer cords. Material red or black plastic. Intended especially for TMT30.

  • Steel ground pick for 4mm banana plug. Typically used for grounding a cable tracer transmitter when the traced object is also grounded or loop currents cause problems and false fields. Length (grounding depth) approximately 25cm. Suitable for devices e.g. CT45 and TM30.

  • SPA10/20 is an accessory for the Vesala cable tracers. It is suitable for tracing e.g. small empty cable piping routes in buildings, prefabricated hollow wall blockages or non-conductive sewers and their blockages. Usage of SPA10/20 resembles usage of the pipe transmitters, which is an independent transmitter.

  • Clamp-on transformers are special accessories for cable tracers and they are intended to be used when direct galvanic connection to cable is not possible. Such targets are e.g. mains cables or cables whose terminals are not available. Also telecom cables, which can´t be connected to without interference, can often be traced with Clamp-on transformers. The PM34 fits around a cable with 34mm...

  • Clamp-on transformers are special accessories for cable tracers and they are intended to be used when direct galvanic connection to cable is not possible. Such targets are e.g. mains cables or cables whose terminals are not available. Also telecom cables, which can´t be connected to without interference, can often be traced with Clamp-on transformers. The PM80 fits around a cable with 80mm...

  • SJ12 is a universal banana/banana cable to connect e.g. cable tracer transmitter to the target. The same cable is often used as speech connection with older Vesala devices that have speech communication possibility through banana connectors. The banana plugs can be equipped with several different adapters e.g. for different terminal block types. Cable length is 1.2 meters and it has been made...

  • SJ20 is a universal banana/banana cable to connect e.g. cable tracer transmitter to the target. The same cable is often used as speech connection with older Vesala devices that have speech communication possibility through banana connectors. The banana plugs can be equipped with several different adapters e.g. for different terminal block types. Cable length is 2 meters and it has been made of...

  • HM12 is a low-cost standard headset with microphone to be used with field phones for speech communication and with cable tracers for signal listening. Using a headset, hands remain free for the actual work and working is more convenient as ambient noise is reduced. The headsets have well-fitting ear-cups and a sensitive electret microphone. Microphone boom is adjustable and can be rotated....

  • MPL6 is micro-sized transmitter sonde for tracing microduct and other tube blockages. It has only 6.4mm diameter so it fit into ducts having inner diameter of 8mm or more. MPL6-10 is compatible with Vesala’s 10kHz wire and cable tracers.

  • MPL7 is flexible and only 7mm diameter transmitter sonde for tracing microduct and other tube blockages. It is very useful when new cables are to be pushed into old ducts, which already have installed cables or other obstacles. MPL7-10 is compatible with Vesala’s 10kHz wire and cable tracers.

  • MPL9 is flexible and only 9mm diameter transmitter sonde for tracing microduct and other tube blockages. It is very useful when new cables are to be pushed into old ducts, which already have installed cables or other obstacles. MPL9-10 is compatible with Vesala’s 10kHz wire and cable tracers.

  • PL18 is a small pipe transmitter sonde which is an efficient accessory for the Vesala CL43 Compact Locator and other Vesala cable tracers using the 512kHz (PL18-05) or 33kHz (PL18-33) tracing frequency.

Šiuo metu klientų atsiliepimų nėra.

Parašyti atsiliepimą

Kabelis ieškotojas CT45

Kabelis ieškotojas CT45

  • Efficient and versatile cable and wire tracer;
  • For locating telecoms cables & faults and mains house wiring;
  • Helps to distinguish certain cables and wires from others;
  • For tracing buried cables, conduit, sewer-pipes and blockages.

The versatile CT45 cable and wire tracer enables telecom technicians and electricians to locate various types of cables and associated problems. For example, telecom and mains cables, wire pairs, under floor heating cables, cable conduit and even sewer-pipe blockages.

Video examples of use of Cable Tracer CT45

CT45 Basic set

The transmitter and receiver use alkaline batteries and both have clear low battery indication. The receiver has an integrated speaker. An external headset can be used for tracing in noisy environment. CT45 is delivered in a handy carrying bag.

1. Transmitter CTT45, 1 psc.
2. Sending cord SJ20 (banana/banana, 2.0m), 1 psc.
3. Crocodile clips, 2 psc.
4. Receiver CTR45, 1 psc.
5. Inductive rod probe SA1, 1 psc.
6. Inductive close range probe LA1, 1 psc.
7. Capacitive probe KA6, 1 psc.
8. Probe cord AK1 (BNC/BNC, 1.0m), 1 psc.
9. Users manual in English, Finnish, Swedish, or Russian, 1 psc.
10. Batteries, 1 set.
11. Carrying bag KPP6, 1 pcs.



Description Language Ver. Link
CT45 Technical description English 1545 CT45 Datasheet, EN

6 kitos prekės toje pačioje kategorijoje: