EasySplicer mk2 is a Swedish made Fusion Splicer, designed for working daily with fiber optic installations. It´s small and handy to bring along to any kind of work. The construction is made very rugged and even if splicing should take place under good conditions (indoors) it is still designed to be used out in the field.
Hoiatus: Viimane toode laos
EasySplicer mk2 differs a bit from other Fusion Splicers as it is made with focus on the installer/user. Many of the Splicers on the market are, even if very competent, difficult to use and require a lot of education before they can be operated.
EasySplicer mk2 is very easy to learn how to use. It doesn´t take more than an hour for anyone to learn and start working with it.
EasySplicer mk2 operates with three buttons only and mostly the user only have to use the main button to perform the splicing.
Still, the precision of the unit is extremely high. It makes typical splicing with a loss of 0,03 dB (Single mode). After splicing it pull tests the splice and makes a loss estimation of the splice were it also tells if something is wrong. Such information is also provided before splicing (like; Bad fiber , Dirty fiber and Too much offset ). The battery-pack inside the unit is small but very powerful. The
unit can perform some 60 splices before it needs to be recharged. Extra battery-packs can also be sold separately (and easily be
exchanged in the unit by the installer).
EasySplicer mk2 is constantly calibrating itself for environment changes (like; moisture, air pressure and temperature). This can also be done manually, for ex. when starting the work of the day. Calibration is very easily performed (within seconds) and makes sure that the splicing is made perfect.
EasySplicer mk2 is using the V-grove method for splicing (same as Ribbon-splicers are using) which has made it possible to keep the size small of the unit. It is easy to service and maintain (even by the user). In all it makes this unit extremely cost effective. EasySplicer Fixed is one of the most inexpensive splicers on the market, yet with a performance of 3-4 times more expensive
EasySplicer mk2 is upgraded with a ceramic/teflon-heater which also is ready for SOC-connectors (Splice on Connectors).
The EasySplicer mk2 is truly a grand innovation for making Fiber optic networks. It will revolutionary the ease to build such networks and it will cut the costs for the customers which will generate more work for the installers!
|Ekraan||LCD, color, 2,8″, 320×240 pixels|
|Ühendused||USB, mini usb plug|
|Patareid||Built in 3400mAh Li-Ion battery pack|
|Tööaeg||60 splice + oven cycles|
|Töötingimused||0-40°C, max 95% RH, non-condenced. Automatic up to 4100 meters altitude with compensation for moisture and temperature|
|Kiude arv||Ühene (Single)|
|Rakendatav kiud||SMF, MMF 50/125μm and 62.5/125μm fiber, 250μm primary and 900μm secondary coated fiber.|
|Kaitsekate läbimõõt||Max 64mm length, 2-5mm diameter supported by oven.|
|Keevitusrežiim||2 pre-defined. SMF & MMF|
|Kuumutus režiim||Ceramic/teflon-type. 40mm sleeves in about 35 sec.|
|Tüüpilised ühenduse kaod||0.03dB SMF, 0.01dB MMF|
|Keevituse aeg||7s + 35s (splice cycle+ oven cycle)|
|Keevituse kadu hindamine||Available|
|Tulemuste salvestamine||Internal 1MB, External SD-Card|
|Kiu kuva ja suurendamine||Camera 140x|
|Toiteallikas||External power supply, 6V, 1.5A, 100-240VAC 50-60Hz|
Hetkel pole ühtegi ülevaadet